LTE Physical Layer Overview - Part IIIPHYSICAL CHANNELSDownlink Physical Channels LTE defines a number of downlink physical channels to carry information blocks received from the MAC and higher layers. These channels are categorized as transport or control channels. Transport Channels. Physical Broadcast Channel (PBCH): The PBCH broadcasts a limited number of parameters essential for initial access of the cell such as downlink system bandwidth, the Physical Hybrid ARQ Indicator Channel structure, and the most significant eight- bits of the System Frame Number. These parameters are carried in what's called a Master Information Block which is 1. The PBCH is designed to be detectable without prior knowledge of system bandwidth and to be accessible at the cell edge. The MIB is coded at a very low coding rate and mapped to the 7. PHY layer: - LTE release 12 compliant. RLC, PDCP and RRC layers. Fiche produit amari lte 100 v5 Author. Protocol Signaling Procedures in LTE By: V. Srinivasa Rao, Senior Architect & Rambabu. Protocol Signaling Procedures in LTE LTE-Advanced Radio Layer 2 and RRC aspects. Thank you for visiting Netmanias! Radio Layer 2 and RRC aspectsRadio Layer 2 and RRC aspects Outline E. Radio Resource Control OSI model by layer; 7. OSI model by layer; 7. NNTP; SIP; SSI; DNS; FTP; Gopher; HTTP; NFS; NTP; SMPP; SMTP. RRC messages are transported via the PDCP. Release of SRB1/ SRB2/ DRBs, ect; Measurement control; Security control. Including the generation of access layer security key, etc; Mobility control. Including the handover management, the cell selection and. RBs) of the OFDM structure. PBCH transmission is spread over four 1. Error! Reference source not found. Each subframe is self decodable which reduces latency and UE battery drain in case of good signal quality, otherwise, the UE would 'soft- combine' multiple transmissions until the PBCH is decoded. The PBCH is transmitted using Space Frequency Block Code (SFBC), a form of transmit diversity, in case of multiple antennas thereby allowing for greater coverage. Physical Downlink Shared Channel (PDSCH): The PDSCH is the main data bearing channel which is allocated to users on a dynamic and opportunistic basis. The PDSCH carries data in what's known as Transport Blocks (TB) which correspond to a MAC PDU. They are passed from the MAC layer to the PHY layer once per Transmission Time Interval (TTI) which is 1 ms (i. To guard against propagation channel errors, convolutional turbo coder is used for forward error correction. The data is mapped to spatial layers according to the type of multi- antenna technique (e. Physical resources are assigned on a basis on two resource blocks for one TTI (1 ms). This is referred to by 'pair of resource blocks' which is the quantum of resources that can be allocated. It corresponds to 1. Hz) for 1. 4 OFDM symbols (normal CP mode). The PDCH is also used to transmit broadcast information not transmitted on the PBCH which include System Information Blocks (SIB) and paging messages. However, MBMS are not included in the first release of LTE. The PMCH is designed for a single- frequency network and it requires that the base stations transmit with tight time synchronization the same modulated symbols. The PMCH is transmitted in specific dedicated subframes where the PDSCH is not transmitted. Control Channels. Control occupy the first 1, 2, or 3 OFDM symbols in a subframe extending over the entire system bandwidth as shown in Error! Reference source not found. In narrow band systems (less than 1. RBs), the control symbols can be increased to include the fourth OFDM symbol. Physical Downlink Control Channel (PDCCH): The PDCCH carries the resource assignment for UEs which are contained in a Downlink Control Information (DCI) message. 3.1.7 PDCP Layer 7 3.2 Life of an LTE Packet: Uplink 8. LTE is the latest generation of the 3GPP standards. 2 Long Term Evolution Protocol Overview Freescale Semiconductor. Physical Layer measurements in 3GPP LTE Author. LTE Radio Layer 2, RRC and Radio Access Network Architecture. LTE -Uu E-UTRAN MME S11 Serving S5 Gateway PDN Gateway. Multiple PDCCHs can be transmitted in the same subframe using Control Channel Elements (CCE) each of which is a nine set of four resource elements known as Resource Element Groups (REG). QPSK modulation is used for the PDCCH. Four QPSK symbols are mapped to each REG. Furthermore, 1, 2, 4, or 8 CCEs can be used for a UE depending on channel conditions to ensure sufficient robustness. Physical Control Format Indicator Channel (PCFICH): This channel carries the Control Frame Indicator (CFI) which includes the number of OFDM symbols used for control channel transmission in each subframe (typically 1, 2, or 3). The 3. 2- bit long CFI is mapped to 1. Resource Elements in the first OFDM symbol of each downlink frame using QPSK modulation. Physical Hybrid ARQ Indicator Channel (PHICH): The PHICH carries the HARQ ACK/NAK which indicates to the UE whether the e. Node. B correctly received uplink user data carried on the PUSCH. BPSK modulation is used with repetition factor of 3 for robustness. Physical Uplink Shared Channel (PUSCH): This channel carries user data. It supports QPSK and 1. QAM modulation with 6. QAM being optional. Information bits are first channel- coded with a turbo code of mother rate of 1/3 before being adapted by a rate matching process for a final suitable code rate. Adjacent data symbols are mapped to adjacent SC- FDMA symbols in the time domain before being mapped across sub- carriers. After this interleaving process, bits are scrambled before modulation mapping, DFT- spreading, sub- carrier mapping and OFDM modulation. Channel coding is similar to that of the downlink. The uplink scheduling interval is 1 ms, similar to the downlink. However, it is possible to 'bundle' a group of 4 TTIs to improve performance at cell edge and reduce higher layer protocol overhead. In this case, a MAC PDU is segmented for transmission over multiple TTIs. In the frequency domain, transmissions are allocated based on multiples of 1. Hz resource blocks. Uplink resources corresponding to the same set of sub- carriers are assigned for the two slots of a subframe. However, inter- slot frequency hopping is an option whereby different sub- carriers are used for the second slot resulting in a frequency diversity gain and averages interference provided different hopping sequences are used in neighboring cells. The PUSCH carries in addition to user data any control information necessary to decode the information such as transport format indicators and MIMO parameters. Control data is multiplexed with information data prior to DFT spreading. Physical Uplink Control Channel (PUCCH): Control signaling comprises uplink data transmitted independently of traffic data which include HARQ ACK/NACK, channel quality indicators (CQI), MIMO feedback (Rank Indicator, RI; Precoding Matrix Indicator, PMI) and scheduling requests for uplink transmission. This channel transmits in a frequency region at the edge of the system bandwidth as shown in Error! Reference source not found. It consists of one RB per transmission at one end of the system bandwidth followed by a RB in the following slot at the opposite end of the channel spectrum thus making use of frequency diversity with an estimated gain of 2 d. B. A PUCCH Control Region comprises every two such RBs. Reference source not found. BPSK or QPSK are used for modulation of PUCCH information. It consists of 7. Resource Block, 1. MHz) as shown in Error! Reference source not found. Preamble Format 0, which is well suited for small to medium size cells (up to approximately 1. Error! Reference source not found. OFDMA with MIMO allows the downlink to provide as high as 1. Mbps in link throughput while SC- FDMA on the uplink reduces design complexity for the user terminals by reducing PAPR. The design of the physical layer and system parameters are well matched with the characteristics of mobile propagation channel to allow optional downlink and uplink frequency selective scheduling thereby enhancing throughput performance. Adaptive modulation and coding maximizes throughput to individual subscribers and increases overall cell capacity. Aside from capacity, the physical layer is structured to provide low latency. The 1 ms subframe duration provides low latency through small scheduling intervals while maintaining low overhead related to higher layer protocols. The PHY is also well designed to provide high cell- edge performance with specific features such as dynamic bandwidth allocation to users and the design of reference signals and control channels which take into account more challenging path loss and interference environment at the cell edge. About the Author. Frank Rayal is the Chief Technology Officer and Co- Founder at Telesystem Innovations. Rayal assists clients with technology and vendor evaluation, business plan and financial modeling, RFI/RFP process, RF network planning and dimensioning, and project management for field trials and network deployment, and product requirement development. Prior to founding TSI, he was Director of Product Management at Redline Communications, where he developed base stations targeted at different market segments and applications and launched end- to- end broadband wireless access networks in emerging markets. Rayal holds a BS in Electrical Engineering from Case Western Reserve University, Cleveland, OH, and a MASc and MBA from the University of Toronto.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |